Factory Direct. You Measure, You Fit, You Save. 1800 016 611
Massive Savings! 40% OFF End of Season Sale Sunscreen Rollers.

How to Measure Shutters

How to measure your shutter before you order it.

It's of course very important that you measure precisely the space into which your Fit-Yourself Shutter is going to be secured.

The shutters we customise for you, based on the specifications you give us, cannot be adjusted once we've delivered them to you.
We can promise and guarantee that we'll send you your customised shutters precisely as per your detailed order. But we can't guarantee that the measurements you've sent us are correct.

Some helpful background information on our high-quality shutters.

Single Panel Shutter

Two-Panel Shutter


AHow to measure for shutters mounted inside the window recess

Naturally, an inside-mounted shutter sits within your window frame. Many regard it as the sleeker and more modern way to install one's shutters, providing you have sufficient depth. There are three inside-mount frame options possible:

Note: It's critical to note there are minimum depth requirements for our Fit-Yourself Shutters to ensure they fit flush with the wall ( please refer to the chart below). If your window opening doesn't meet this minimum requirement, you MUST use an Outside Mount Frame.

 
  Minimum Depth Requirements
Blade Direct Mount L-frame Z-frame
63mm Blades 40mm 40mm 40mm
89mm Blades 45mm 45mm 45mm
114mm Blades 60mm 60mm 60mm

If installation occurs in a window opening without a protruding sill, the inside-mounted Z-Frame will extend around 5mm onto the face of the molding (sheetrock) - See Illustration 2. However, if the sill is protruding, the base of your shutter frame will end at the top of the sill - See Illustration 1.

The decorative trim face of the Z-Frame will cover most of the apparent inconsistencies or any light gaps created due to the window frame not being precisely 'square' and will hide deviations of up to 5mm on either side of the frame

Illustration 1

Illustration 2

Note: It's easy to measure accurately the size of shutter you'll need to fit your window space perfectly but your attention-to-detail is critical.
You must use a steel measuring tape and measure each and every window space as they may well all be slightly different sizes even though they appear identical.

Illustration A

Illustration B

First, decide that there's a minimum clearance of 40mm for Inside-Direct Mount and Inside-Trim Frames, or 50mm minimum clearance for an Inside-Recessed L-Frame.

Please note that special attention should be given to window openings which have:

  1. Sloping window sills
  2. Window cranks
  3. Latches
  4. Security devices
  5. Removeable screens

Any one of these may obstruct the shutter frame. When measuring for our Inside Mount Shutters ensure you have the proper clearance depth shown above, based on your measurement to the front of the nearest obstruction. If you have any queries, please contact us.

How to make your precision measurements for your fit-yourself shutters.

WIDTH
You'll need to measure the width of each window opening in three places: the top, middle and bottom, as shown in Illustrations A and B.

  1. Take the smallest of the three measurements and write it down on a piece of paper.
  2. This width size is the size you will need to order, without making any deductions to it.
  3. Our factory will make a minor deduction to each accurate size you give us to allow for easy installation.

HEIGHT
Measure each window's height in three places: across the top, middle and bottom, as shown in Illustrations A and B. Then, take the smallest measurement and use this as the size you place on your order to us. Our factory will make a minor deduction to this height measurement to allow for easy installation of you new shutter.

HEIGHT AND WIDTH ADJUSTMENTS NEEDED.
Our factory will make any necessary adjustments needed to enable easy self-fitting of your blind. Do not make any adjustments to your measurements. Just send us the precise dimensions you measured carefully.

IMPORTANT NOTE IF THE HEIGHT OF YOUR SHUTTER IS OVER 1800MM.
If your shutter height is greater than 1800mm it will automatically include a centred divider rail.


BHow to measure for Outside Shutters

IMPORTANT NOTE ABOUT THE IMPORTANCE OF ACCURATE MEASURING.
Our Fit-Yourself Shutters are very easy to install but it's essential that the measurement of the window space into which they need to fit, to be very precise. You MUST use a steel measuring tape and measure each and every window, regardless of whether or not they appear identical. In most cases, they won't be.

Our Outside Mounted Fit-Yourself shutter will come to you without and deductions to the sizes you specified on your order to us. When ordering your Outside Mounted shutter, ensure that you specify the 'finished sizes', including the frame.

WIDTH
When determining the finished width of your Fit-Yourself Shutter, make sure you measure the OUTSIDE edge of the architrave ( as shown in the diagram above).

HEIGHT
When measuring a window with no sill, please ensure that you measure the edge of the architrave using a steel measure. Measure from the top of the sill to the very top edge of the architrave ( as shown in the diagram above).

For more information please contact us.

© Copyright 2017 ABC Express Blinds | Outdoor Blinds Perth | Privacy Policy | Disclaimer